Tokyo - Activities | Fill the gap answer
Activities with "Fill the gap answers" allow students to complete texts filling blank fields.
This type of activity is divided in three areas:
A. Wording area. It includes a sample text by default, but other components like images, audios, and videos can be added as well.
B. Answer area. This field is used to write a text including gaps for words that students must insert to complete them.
C. Feedback. It is possible to configure some positive feedback and negative feedback related to questions. Apart from text, feedback can also include an image.
- Step 1. Set up activity properties
- Step 2. Set up the wording
- Step 3. Set up the answer area
- Step 4. Advanced layout design: how to add columns
- Step 5. Configure feedback
Step 1. Set up activity properties
After adding the activity, go to the "Properties" tab and configure them:
Score required to mark activities as complete and get a positive feedback. Getting a 100% score is required by default.
This property is only avaliable with a quiz with a "Quiz" view. All the questions have the same weight by default, but we can modify how much a question counts towards the final score. See here to know how to calculate quiz scores depending on the weight of each question included in the quiz.
This is only applied when we add questions within a quiz with an "Activity block" view (see here).
This property allows indicating the number of attempts available to complete the activity.If you want unlimited attempts, write "0" attempts. (It will only be finished after overcoming the activity).
Distinguish upper case/lower case
This property allows us to determine if students should distinguish between upper case and lower case when writing. The options are:
This property allows choosing if it is required to write word(s) using correct accent marks.
Ignore special characters
This field allows us to indicate the special characters that are not considered when marking an answer as valid. So, we could ignore full stops, commas and similar characters.
Step 2. Set up the wording
1. Write a text for the wording of the question (see here setup options available for texts).
2. Optionally, you can add more components within the wording. Make sure you select the wording (you will easily find it with the breadcrumb trail) before going to the "Add" tab and include the components you need.
Step 3. Set up the answer area
3. There is a text field below the wording. You should write the phrase or content that we want to include. Then, put the cursor over the text area where you want to add a gap. Go to the text editor, click on the "Components" menu and add an "Option". A gap is automatically added inside the text.
4. We can configure options clicking on each gap and going to the "Properties" tab to adjust the following fields:
We should use this property to indicate the right word that students must use to fill the gap. It is important to say that students must write exactly what is written inside this field; otherwise, their answer will not be marked as correct. However, this rule will not be applied if we have decided the lack of accent marks is not penalised.
By default, all blank spaces appear with a "Normal" view, that is, each gap has the same size of the word replaced by it. If we want to edit this size, we select the "Editable width" view.So, if we leave gaps as they are shown by default ("Normal" view), we will be giving hints about the size of word(s) that students need to use. However, we could avoid this using the "Editable width" view to leave the same blank space for every gap.
Size (number of letters)
|This property is enabled if we choose the "Editable width" "View". We will adjust the gap size. This is measured according to the number of letters. So, for the word "team", its minimum width would be 4.|
Step 4. Advanced layout design: how to add columns
Normally wordings and texts are enough to configure activities correctly, but sometimes we want to add especial elements (images, audios, etc.) and create more complex layout designs. We can add "Columns" to create these layouts.Columns can be inserted anywhere: after wordings, after answer options, etc.
Within a column, we can add different elements: images audios, videos, texts, etc. From the "Properties" tab, we can configure properties like "Size", "Offset" and "It's the last column".
Columns occupy 12 spaces inside screens by default (100% of available space). We can modify the number of spaces occupied by columns (1-12) to create different layouts: 2 columns (6 spaces each), 3 columns (4 spaces each), etc.
This option allows creating a breaking space on the left of the column (1-12 spaces). This way we can insert spaces between columns.
It's the last column
This property allows marking an option as the last one within a row. This means that the second column will be placed below the first column, so that the third column appears as the last one within the row. This example shows that more options could have been included in the first row, but we have decided to insert them in the next row.
Use of columns allows creating complex layouts. For example, we could add various audios and texts to complete. The example below shows two columns. Each column occupies 5 spaces and includes an audio file and a text where students need to fill the blanks. Furthermore, offset for the second column is "1", which allows leaving some space between both columns.
Step 5. Configure feedback
Finally, we write the texts of positive and negative feedback to finish the setup.As you can see, the text can be replaced by an image.If you do not want to include any feedback, you can delete it.